升降貨梯http://www.jntr168.com/在使用之前,，一定要按照使用要求來進行調試,，才能夠保證在生產的過程中,，能夠安全的生產,，給操作人帶來安全。那么新買來的升降貨梯如何進行調試呢,？

1,、對于升降貨梯來說，是要調整防墜安全器制動的距離,，按照GB/T10054-19的規定,，它的墜安全器的制動距離應在0.25~1.2m。并不是制動距離越短就越好。相反,，制動距離越短,，所產生的沖擊力就越大，對機構造成的破壞就越大,，特別是高速升降機,，其危害尤為嚴重。
For cargo lifter, is to adjust the anti-fall safety braking distance, in accordance with the provisions of GB / T10054-19, the braking distance of its fall safety device should be 0.25 ~ 1.2m. The shorter, the better is not the braking distance. On the contrary, the braking distance is shorter, the impact force generated by the greater damage to the body caused by the greater, especially in high-speed lift, which is particularly serious harm.

2,、升降貨梯需要調試壓輪及滾輪,，安裝前先將吊籠和驅動機構的全部偏心滾輪軸松開或?qū)⑵木嗾{(diào)至最大，分別將吊籠和驅動機構安裝于導軌架中,，并將兩者連接,。通電驅動吊籠上升離地面lm或脫離地面緩沖彈簧為止。
Cargo lifter need to debug pressure wheel and the wheel, install all the eccentric roller shaft hoists and before the first release of the drive mechanism or the eccentricity to the maximum, respectively, hoists and drive mechanism mounted on the frame rails, and the two connection. Powered drive cage lm rise from the ground or from the ground up buffer spring.

3,、升降貨梯http://www.jntr168.com/需要調試制動器,，制動力矩越大制動時的沖擊就越大，制動力矩過小時,，會造成吊籠下溜或撞擊事故,。對于有多個制動單元的驅動機構，其每個制動器之間的制動力矩的誤差應≤10nm,，否則會造成個別制動塊(盤)燒損,。
Cargo lifter need to debug brake, brake torque the greater the impact on the greater braking, the braking torque is too small, will cause the next cage slip accident or collision. For multiple braking unit drive mechanism, each brake braking torque between the error should ≤10nm, otherwise it will create individual brake pads (disc) burning.